1 Gallon Capacity Add-It Fertilizer Injector with 1" Female Pipe Threads

Description

1 Gallon
Capacity Add-It Fertilizer Injector
with 1" FPT inlet x 1" FPT outlet
Additional sizes are available!
Model AFI 1010
ASAE award-winning Add-It proportioning fertilizer injector
A Minimum of 5 GPM flow rate and 10 PSI is required to operate!
There is NO pressure loss!
This injector can be be installed under constant pressure up to 80 PSI!
A backflow prevention devise should be installed upstream of the injector
Description
ASAE award-winning HEAVY DUTY Add-It proportioning fertilizer injector and foliage feeder with 1 gallon capacity and 1" FPT inlet 1" FPT outlet.
A minimum of 5 GPM and 10 PSI is required to operate! There is NO pressure loss! It can be installed under constant line pressure!.
This injector is proportioning. The injection rate stays the same from start to finish, 200:1, that’s 200 parts water to 1 part additive, unlike most other injectors on the market today.
This injector is of particular benefit to those who use a drip irrigation system, because an injector is the only means of fertilizing easily, efficiently and economically.
If utilizing a drip irrigation system in order to conserve water as well as save time, no longer can you broadcast dry granular fertilizer to the soil surface and expect it to be leached into the soil where the plants roots can pick-up the nutrients. Therefore, the fertilizer must be dispensed directly through the drip irrigation system.
(Used units cannot be returned for any reason except for warranty replacement.)
Built to last longer than just one season! Proudly made in the USA!
Operating the 1 gallon
capacity Add-It fertilizer injector
If using a premixed liquid, usually you can pour it in full strength. To save even more money, we highly recommend using a dry, totally water-soluble granular fertilizer such as Scotts Miracle-Gro® or Peters Professional®, Bandini Pro Choice®, or Grow More®. Simply premix the dry fertilizer with water at a ratio of 1 to 1¼ pound of dry formula (i.e. one small bag of Miracle-Gro® general purpose plant food, 15-15-15 or 20-20-20) to 1 gallon of water. Easy, mix (1) bag of Miracle-Gro® to (1) gallon of water
As you operate your irrigation system, a small amount of water is diverted from the mainline into the top of the additive tank.  The solution of fertilizer is drawn from the bottom of the tank. The incoming water and the additive in the tank do NOT blend.  After all the additive has been dispensed, the tank will be full of water.  When you want to refill the unit with additive, simply drain the tank, and refill the unit.
It will take approximately 200 gallons of water passing through the injector, and your irrigation system, to dispense all of the additive in the tank. If you have a flow rate of 1 gallon per minute (GPM), simply divide 200 by the flow rate of 1 GPM. You now know it will take approximately 200 minutes, or a little under 3
½
hours, to not only water your trees, shrubs and lawn, but also fertilize them as well.
To initially fill the Add-It fertilizer injector and foliage feeder, remove the top fill cap. Insert the fill funnel into the opening and pour in liquid solution. Fill the tank
completely
.  Replace the top cap, and the Add-It fertilizer injector is ready for operation. Turn on the irrigation system .
When the time comes to refill the Add-It injector, turn off the water supply. Remove both the bottom drain cap and the top fill cap. Allow all of the water to drain from the unit and replace the bottom drain cap. Place the fill funnel in the top opening and recharge the Add-It injector. Replace the top fill cap and turn on the irrigation system. Once you have completed watering, it is not necessary to drain the unit. If there is fertilizer or additive still in the tank, it will be dispensed the next time you operate your irrigation system.
Check out all our injectors listed in our eBay Store for your fertigation needs.
NOTICE!
When purchasing more than one item we will combine shipping charges whenever possible.
After
placing your order, but
before
paying for your order, please
request
an invoice.
Please take a look at all the products we offer in our eBay Store!
Feedback Policy
We give feedback on all
completed
transactions. We consider a transaction complete after the following: You have paid, we have shipped, you have received the item to your complete satisfaction, and have left us feedback. Once you leave us feedback, our feedback is usually left within 48 hours. Thank you!
Terms & Conditions of Sale
Products may not be returned for ANY reason without prior authorization. A RGA number is essential and may be obtained from the order desk. Claims for defective material MUST be made within thirty (30) days from receipt of goods. Claims for damaged goods should be made directly to the freight carrier, not the factory. Hold onto damaged goods, in the original containers, until they have been inspected.