303-761 6.0L Powerstroke Front Crank Wear Sleeve Installer - Tool, Sleeve & Seal

Description

Compatibility: Fit for 2003-2010 Ford Powerstroke 6.0L (Replaces Motorcraft/OTC OE# 303-761)
High Quality: Machined from stainless steel and rubber with excellent mechanical and physical properties, this Installer Tool Set is good in corrosion resistance and durability
A-Must-Have: Oil leaks from the front crank seal are a very common problem on the 6.0L Ford Powerstroke Diesel Engine. This tool kit helps install the delicate wear sleeve to the correct depth without any damage
Easy To Use: Radiator, fan and shroud removal is not required. This tool allows you to perform a job that normally takes 3 hours in 1 hour!
100% SATISFACTION GUARANTEE: Our tool set is simple to use, impossible to mess up, and well built. If you're not 100% satisfied with Sunluway Front Crank Wear Sleeve Installer Kit, simply return it for a full refund in 30 days. Premium Support & 12-Month Warranty
Product description
Oil leaks from the front crank seal are a very common problem on the 6.0L Ford Powerstroke Diesel Engine. The Ford special tools required for this job require 3 hours book time to use following the factory procedure. Using our wear ring installer and procedure the job can be performed in about an hour. Unlike the factory method, our tool does NOT require removing the radiator, fan, and shroud. The job is nearly impossible to perform without an installation tool due to the delicate nature of the wear sleeve, the location of the harmonic balancer dowel pin, and the fact that the wear sleeve must be driven to a specific depth beyond beyond flush to position in properly. Attempts to install the sleeve without correct tooling usually result in leaks and comebacks.
Front Crank Wear Sleeve Driver/Installer Kit Tool with Sleeve & Seal
Fitment:
Fit for 2003-2010 Ford Powerstroke 6.0L
Replacement:
Motorcraft/OTC 303-761
Material:
High quality steel and rubber with durable
How to Use 6.0L Powerstroke Front Crank Wear Sleeve Driver/Installer Kit Tool with Sleeve & Seal
Begin by breaking loose the four front crankshaft dampener bolts. Then remove the belt. (The belt just needs to be slid off the upper idler pulley to allow enough slack to remove the crank pulley.) Finish removing the bolts and the front pulley. Fan, shroud, and radiator are shown removed for clarity, but removal is not required.
Remove the five 10mm bolts that attach the oil pump cover and crank seal.
With the cover removed, clean the oil from the area around the pump.
Tape the area as shown with wide masking tape to prevent debris from getting into the pump gears.
Use a small cut off wheel to carefully cut through the old wear sleeve (if present) and remove the sleeve.
Clean the crankshaft - fine sandpaper may be required.
Install the new wear sleeve into the tool and coat the inside of the sleeve with a light layer of red Loctite.
Slide installer and sleeve onto crankshaft
Lightly tap installer with a hammer until it bottoms out.
Remove installer - your sleeve is now installed to the correct depth. Remove tape, clean surfaces thoroughly, and apply some engine oil to the pump gears. Install new seal into pump cover and complete reassembly.
Installer-Front
Installer-Back
Sleeve
Seal
Payment
We accept PayPal payment only.
Shipping Policy
Orders will be ship out within 1-2 business days after payment has cleared. Orders from Saturdays, Sundays or holidays will process on next business day and will be ship within 24 hours. Please allow 10-30 days for international deliveries. Some shipments could take longer subject to your local customs authorities.
United states
2-5(days)
Return & Warranty
Any defective items received can be replaced or refunded. Please contact us with the item number, eBay ID and defect description within 7 days after the date of package arrived.
No Claim will be accept after 7 days.
About us
We, running a family-owned business,
is committed to providing the best quality products, competitive prices and services beyond customer expectations.
Our company began in 2
009
and we mainly sell professional tools, auto parts and decoration. We also provide added-value to our business customers.
We believe customers in today's market are more demanding than ever and they deserve the best!
Contact us
If you have any questions, please feel free to email our service specialists 24 hours a day, 7 days a week. We will reply you ASAP
, but there may be some delay during weekends or holidays.
About Feedback:
If you are not satisfied for any reasons, please do not be so quick to leave negative/neutral feedback. We work hard to make sure EVERY CUSTOMER 100% SATISFIED and resolve any problems for you and always leave positive feedback to all our customers.
If you are satisfied with the product you received, please kindly leave us a positive feedback and 5 scores DSR. Thanks!