Olympus XA Custom Light Seal Kits | USCamera Online Since 1998 | 3 PACK SpeciaL

Description

USCamera Custom Light Seal Kits
Olympus XA Film Cameras
Special Buy 2 Get 1 Free
Each 6-piece kit includes 2 channel seals for the camera body lower/upper, back cover upper/lower channel seals, 1 door latch plate seal on the back cover, and 1 door hinge seal on the camera body.
These USCamera custom light seal kits will fit the Olympus XA film cameras only.
This purchase is for three complete light seal kits.
All seals have adhesive already applied and to install you just peel off the backing and press into place.
We make Top Quality kits using premium imported black open cell foam.
Ebay no longer allows us to provide a help link for installing kits here.
We package website link information with every light seal kit. See our website for detailed removal and installation instructions. Many model specific seal placement guides available also.
What makes a premium USCamera light seal kit?
USCamera light seal kits were designed and used by technicians years before the internet. The same quality kits we sell today.
Our kits start with imported premium quality open cell foam from Japan. The same type of foam camera engineers designed cameras to use. For every kit we make, we have samples of that equipment ... cameras, film backs and more. Our kits start with accurate measurements taken directly from the sample. Many times we can compare those measurements to brand new original factory seals. Then we use various widths of material to find the perfect fit for the door channels and where additional seals are required. We guarantee them to fit the equipment listed. All seal kits are randomly checked for the correct number of seals and proper fit by actually installing the sample kit.
Why buy a kit? You can save time and be confident knowing you are installing a proven product. Sure, you can save money by purchasing bulk foam material and cutting your own kits. We found it takes 1 - 2 hours to measure, cut and fit a custom cut kit. The more kits you make the better you get. Cutting open cell foam takes practice. However, even technicians who have cut foam for years have problems cutting thin strips accurately and consistently.
Your equipments value could be affected by using anything other than type of seals/material than what the engineers originally installed. Premium black open cell foam with high pore count per 25mm. Light seal foam is a specialty item. Requiring very tight thickness tolerances, close to 1.5%.
You can save money and use yarn. Some people suggest that on the internet. Yarn had a lot of "fuzzies" exposed in the door channel. In the past, we tried yarn to preserve some collectable cameras perceived value. We found it time consuming to work with. I am sure you would get better with experience however it is very difficult to produce a clean install. Small pieces of yarn debris, furry looking particles, dirt or ? on the negatives......get the picture.
You can bow a cameras back cover and make it hard to close, if too thick of any material is used in the camera body door channels or back cover. You do not have to worry about that with a USCamera light seal kit.
Camera design engineers had various materials available to them as camera designs improved over the years. They used and still use premium grade open cell foam in imaging equipment.
Lastly, in the last few months I have noticed new vendors selling light seal kits where some pieces are cut and some are not. Usually the channel seals are the pieces left that need cutting. From someone who has cut foam for years, if you don't have to, you do not want to hand cut your own seals, especially the channel seals. Think about it, the camera body door channels provides the largest area of possible exposure of your film to light leaks.
Anything foam cut under 2mm wide becomes a real challenge on cutting consistently. I found the waste as high as 40% to a low of 15% even after I figured out a way to measure the width more accurately. That's the difficulty, each time you cut a new piece, you have re-position the cutting guide and measure the width.
I wish you good luck with your light seal kit install. Sincere thanks for your continued use of film equipment as it keeps film camera technicians like me busy doing something we really enjoy.
Image(s) shown of the actual item. Unless we describe the item otherwise, you should expect it to be new. Please read our descriptions and look at the images carefully. If something is not shown in the images or not listed in the description then it is not included. This kit will only fit the model(s) listed. Just because the picture looks like or identical to the pieces you believe your equipment will require, does not mean this kit will fit your equipment. Again if your equipment make and model is not listed in the ad, this kit will not fit your equipment. If you have any questions, please ask before you purchase.
We have graded this item as New condition.
For more information on our grading system go
here
.
Shipping
:
We print shipping labels out through PayPal. Please make sure your shipping address with PayPal and eBay are correct. We are happy to combine items for shipping. Free shipping to US addresses only.
Payment
:
Please complete payment arrangements within 48 hours from close of auction.
USCamera has been serving photo enthusiasts on the web since 1998.
You may email us any time.
Email answered within 48 hours
, except on weekends and Holidays.
©USCamera.
All rights reserved.
Material and images on this page are the copyrighted property of USCamera and may not be used without the prior written permission of USCamera.
ls-olmypus XA-3PACK